Member postings for speelwerk

If you want a good one I would choose this, Niko **LINK** https://www.heuer.de/fileadmin/content/Bilder_content/Compact/Produktinformation-2Seiter/Product_information_compact_set_en.pdf

Edited By speelwerk on 29/04/2021 21:59:06

I just cut it on the workbench which is made out of melamine board and changed every year or so when it has to many (cut) marks. With a sharp knife it stays straigth and leaves almost no bur. Niko.

Perhaps not possible with stainless (never tried) but 0.1 mm brass cuts easily with a Stanley knife along a ruler. Niko.

Annealed or hardened, I would heat it to red to make that bend. Niko.

https://codeandlife.com/2012/03/06/weller-magnastat-autopsy-and-repair/

Here you can buy a new one but you will have to overcome the benefits of Brexit **LINK**

http://www.myfordsolutions.nl/contents/nl/p91.html

Niko.

Edited By speelwerk on 04/03/2021 13:20:23

I became so angry at them last week after being harassed now for several weeks by the same caller/number claiming I registered at “Lux Investment” and wanting further details from me that I named them everything I could think of in my not so good English. That made them angry and threatened to sue, to which I replied that I am waiting for it. After that almost continues calling from first a English 0044 number, after blocking that it changed to Italian 0039 and then to Polish 0048. The result is that I now have blocked all incoming international 00 numbers, hopefully they will now give up and normality can return in the near future. Niko.

Safe to use?

She is checking if the lathe complies to the higher standard of British health & safety regulations going in force January 1ste 2021.

This is similar, silversteel, diameter 2.8 mm, core 0.9 mm, pitch 1.10 mm and 8 turns if it becomes more slender you make an extra support. Niko

Don't know about passivated plasterboard screws but would stainless not be better to use in the bathroom? Niko.

It is just possible to fit the large 72 tooth gear of the quick change gearbox on a clutch, it prevents damage if a crash happens. Niko.

I never hear anything about money cost of repair, do they work for free? Niko.

Although from a MK.1 this might help, **LINK** Niko.

Edited By speelwerk on 01/09/2020 23:55:28

Thanks all! Lots of possibilities, I like the paraffin one. Niko.

Edited By speelwerk on 15/08/2020 10:02:26

Would a silicone spray prevent a metal (silver) hinge from sticking to a casting epoxy resin, or should I use something else? Niko.

Am I seeing this wrong way around or is this a lathe rYAAOSwhdVfDZKL">https://www.ebay.de/itm/Watchmakers-lathe-BOLEY-LEINEN/274439614604?hash=item3fe5e0308c:grYAAOSwhdVfDZKL special made for the left handed watchmaker? Niko.

For small taps (<M 2) I use a pin vice but this is also a nice one **LINK** Niko.

It is not difficult to find items on Ebay which have been "sold" but are offered again by the same seller. How they do it without paying sellers fee (Ebay & Paypal is around 15% together) is a question for me. Niko.

Edited By speelwerk on 22/07/2020 21:54:28

Thanks!

I should have made the taper a little less steep, 2 instead of 3deg. Niko.

Over the weekend I made an attempt to improve the pulley fitting by making a conical plug pushed in by a M6 screw in the motor shaft. It gave not the improvement I hoped for but a wobble of around 0.10 mm is good enough for me. Niko.