By continuing to use this site, you agree to our use of cookies. Find out more

Member postings for V8Eng

Here is a list of all the postings V8Eng has made in our forums. Click on a thread name to jump to the thread.

<< First < Prev 81 82 83 84 85 86 87 88 89 90 91 Next > Last >>
Thread: Milling from a sheet
12/11/2011 21:30:35

 
 With energy prices now, they probably can't afford to run the oven anymore!
 
 

Edited By V8Eng on 12/11/2011 21:57:12

11/11/2011 19:40:01
I was reading Alan's post yesterday looking for a set of rolls for building his 1:1 scale Titanic.
 
Large sheets can be tricky without a generous supply of tea and biscuits, guess that's where you've gone during the first photo.
 
 

Edited By V8Eng on 11/11/2011 19:46:46

11/11/2011 19:22:49
I think Alan Frost might like these.
They might work for some of the smaller parts on a 1:1 scale Titanic, I look forward to seeing it at next years Sandown!
 
 

Edited By V8Eng on 11/11/2011 19:27:31

Thread: Building a miniature universal lathe
27/10/2011 19:28:29
Hi.
 
I have a book called "Building a Small Lathe" by L C Mason, this describes building a 1 3/4" centre height machine.
It was published in 1977, but I think TEE publishing supply a reprint.
 
Might be worth checking whether it would help you.
 
 
 
Thread: Fastners in Birmingham
13/10/2011 21:40:09
You could try phoning this one to see if they stock what you want, and if collection is available.
I think they are in Walsall which is about 14 miles from Birmingham.
 
Thread: Darracq
12/09/2011 19:53:59
Hello.
 
Sorry I seem to have posted an empty space yesterday, it should have been a couple of websites.
 
 
 
Regards.
12/09/2011 19:53:56
Hello.
 
A couple of websites that might be of use.
 
 
 
Regards.

Edited By David Clark 1 on 16/09/2011 08:50:47

Thread: 3/8" BSF stainless steel grub screw supplier?
28/08/2011 17:33:57
Hi.
 
You could try this supplier.
 
 
Regards.
 
 

Edited By V8Eng on 28/08/2011 17:36:19

Thread: Explorer 9
17/06/2011 18:52:20
Steambuff.
 
Thanks for that info, I have been having the same trouble as John.
It is working now after using compatability mode.

Edited By V8Eng on 17/06/2011 18:53:51

Thread: Resilient Mountings
31/05/2011 21:16:37
Hi.
 
If you only need the resilient mounting parts, it might be worth checking if there are any electric motor repairers / rewinders or similar concerns in your area and asking them.
 


Edited By V8Eng on 31/05/2011 21:19:20

Thread: Forward reverse switch diagram
28/05/2011 18:02:13
I do not have a wiring diagram but it might be worth checking out the Kraus & Naimer website, and possibly emailing them for info.
 
http://www.krausnaimer.co.uk
Thread: Modern Steam Engines
30/04/2011 20:53:15
 
I think a British car has held this record since 2009, managed to find the website address from that time.
 
http://www.steamcar.co.uk/
 
Sorry that is not a hyperlink, I cannot seem to make those work at the moment.
 


Edited By V8Eng on 30/04/2011 20:57:30

Thread: brass wire mesh in 1mm weave
28/04/2011 19:01:04
Two more possible suppliers to look at.
 
www.wires.co.uk
 
www.wovenwire.co.uk
 

Edited By V8Eng on 28/04/2011 19:02:09

Thread: Nickel Plating
19/04/2011 12:35:38
There is a very good book on this subject, number 11 in the Workshop Pactice Series,
It is called Electroplating (by J Poyner).
This is very much a practical book and the subject is very well covered (please excuse the pun) from principles to chemicals, equipment used and power supplies.

Thread: New I/C diesel project - ETA15d-x2
17/04/2011 18:42:17
Hi Ramon.

GLR distributors advertise nickel plating kits in ME.
 
http://www.modelmakingsupplies.co.uk
 
 
Thread: Aircraft General Discussion
04/04/2011 19:24:35
Hi Les.
 
OOPS!

Thanks, I usually get links right, must be having an off day.
Thread: Countryman's Steam - Chain drilling
04/04/2011 17:42:54
 
 
Thanks Jason, I do get my copy from shop so look forward to reading the next part.

Edited By V8Eng on 04/04/2011 17:44:19

Thread: Aircraft General Discussion
04/04/2011 16:39:59
 
Do not forget about the last flying Vulcan Bomber.
Please go to the website for news on it.
 
 



Edited By V8Eng on 04/04/2011 16:52:33

Thread: Countryman's Steam - Chain drilling
04/04/2011 16:17:45
 
I cannot find anything about the Countryman's Steam series in issue 4400, it does not seem to be in the 'next issue' listing for 4401 either.
 
Where are you finding the drawings and ongoing articles?
 

Edited By V8Eng on 04/04/2011 16:19:21

Thread: Countryman's Steam.
15/03/2011 20:27:01
Hi.
Thank you.
<< First < Prev 81 82 83 84 85 86 87 88 89 90 91 Next > Last >>
Magazine Locator

Want the latest issue of Model Engineer or Model Engineers' Workshop? Use our magazine locator links to find your nearest stockist!

Find Model Engineer & Model Engineers' Workshop

Sign up to our Newsletter

Sign up to our newsletter and get a free digital issue.

You can unsubscribe at anytime. View our privacy policy at www.mortons.co.uk/privacy

Latest Forum Posts
Support Our Partners
cowells
Sarik
MERIDIENNE EXHIBITIONS LTD
Shopping Partners
Subscription Offer

Latest "For Sale" Ads
Latest "Wanted" Ads
Get In Touch!

Do you want to contact the Model Engineer and Model Engineers' Workshop team?

You can contact us by phone, mail or email about the magazines including becoming a contributor, submitting reader's letters or making queries about articles. You can also get in touch about this website, advertising or other general issues.

Click THIS LINK for full contact details.

For subscription issues please see THIS LINK.

Digital Back Issues

Social Media online

'Like' us on Facebook
Follow us on Facebook

Follow us on Twitter
 Twitter Logo

Pin us on Pinterest

 

Donate

donate