By continuing to use this site, you agree to our use of cookies. Find out more
Forum sponsored by:
Forum sponsored by Forum House Ad Zone

crap-o-matic

All Topics | Latest Posts

Search for:  in Thread Title in  
Michael Gray14/10/2009 22:06:04
avatar
45 forum posts
6 photos
Ian, I bought one of these years ago in the dreaming hope it woudl help me.  All it did was drain my bank account buying new oxygen  bottles.
Finally found a secondhand shop in Prince George that sold me a plumber''s oxy-acetylene set with small tips ideal for model engineering for 200 bucks - and both tanks were full!!   Best buy I ever made.
regards, Mike
Frank Dolman15/10/2009 08:53:34
106 forum posts

 
     I can endorse Mike's remarks.  I borrowed one from my brother, ignoring
 his warnings, to braze a 1.25" tube into a hole in 16 swg sheet.  The job used
  three bottles of O2. @£6.
keithmart15/10/2009 10:13:23
avatar
165 forum posts

Hi


I purchased a similar set up and have the same problem.


Oxygen cylinders last about 5 minutes, at around £6.00 each.


Cheaper to buy a big set!!


regards


Keith


Leeds UK

Ian Abbott15/10/2009 19:51:14
avatar
279 forum posts
21 photos
I bought the Bernz set as something that I could literally stick in my pocket and carry on to the boat or into the middle of a field, where the big bottles just weren't practical.  I started with a couple of bottles of each gas, which I'm still using after about fifteen years.  On the job, the price of gas wasn't a consideration though, the customer paid.
 
It works well for what it is and does the job at a reasonable price.  If I were looking at buying £500 worth of equipment for the occasional hobby job, £6 a bottle for oxygen might be a sensible alternative.
 
Having said that, I wouldn't even try to use it for a job where more than a couple of minutes heating is required, but I have brazed 1/4" stuff with it.
 
On full size welding sets, I bought two new commercial Oxy-Acetylene sets in 1981 for something like $50 each.  I used one until we left Canada last year which I sold for $75.  Now, I'm getting out the "brand new" set which has been in it's box for 28 years.
 
And, I picked up a £40 stick welder from Lidl a couple of months ago which we've been using to weld 3/8" steel on the combine harvester and hedge trimmer on the farm.  It's got a slow recovery cycle, but at £40, I can talk to the cows while I wait.  The thing is that it can be turned down to handle 1/6" sheet quite happily.
 
Ian 
David Burns20/10/2009 02:48:12
1 forum posts
Gday from Australia;        I agree with Ian Abbot on the Bernz kit . I bought a kit about 20 years ago and found it ideal for small bronzing jobs in model engineering.
 
Unfortunately our lords and masters down here dont allow the oxy bottles to be sold any.more.    Dont know why.
 
 Could be the big industrial gas sellers have pulled some strings.
 
 Dave.
Michael Gray20/10/2009 17:40:44
avatar
45 forum posts
6 photos
Posted by David Burns on 20/10/2009 02:48:12:

 (snip)
Unfortunately our lords and masters down here dont allow the oxy bottles to be sold any.more.    Dont know why.
 
 Could be the big industrial gas sellers have pulled some strings.
 
Could be they were ashamed of the huge profit they were making on the itty-bitty oxygen bottles?  
regards, Mike

Edited By Michael Gray on 20/10/2009 17:41:14

Ian Abbott20/10/2009 20:18:11
avatar
279 forum posts
21 photos
I did entertain thoughts of a link between the big bottle of oxygen and the little one to top it up, but sense prevailed, not knowing what the pressure in the small one would be, there being no gauge.  Next time I go to our gas supplier, I'll find out what it'll cost me for a new one when I finally use up the originals.
 
I did think that the small bottles would make a nice reservoir to even out the flow of air from the little 12v compressor, so that I could use it  on my airbrushes.  Much more convenient than a 2hp job, which I haven't got around to buying new yet.   Better than junking them.
 
Ian 

All Topics | Latest Posts

Please login to post a reply.

Magazine Locator

Want the latest issue of Model Engineer or Model Engineers' Workshop? Use our magazine locator links to find your nearest stockist!

Find Model Engineer & Model Engineers' Workshop

Sign up to our Newsletter

Sign up to our newsletter and get a free digital issue.

You can unsubscribe at anytime. View our privacy policy at www.mortons.co.uk/privacy

Latest Forum Posts
Support Our Partners
cowells
Sarik
MERIDIENNE EXHIBITIONS LTD
Subscription Offer

Latest "For Sale" Ads
Latest "Wanted" Ads
Get In Touch!

Do you want to contact the Model Engineer and Model Engineers' Workshop team?

You can contact us by phone, mail or email about the magazines including becoming a contributor, submitting reader's letters or making queries about articles. You can also get in touch about this website, advertising or other general issues.

Click THIS LINK for full contact details.

For subscription issues please see THIS LINK.

Digital Back Issues

Social Media online

'Like' us on Facebook
Follow us on Facebook

Follow us on Twitter
 Twitter Logo

Pin us on Pinterest

 

Donate

donate