By continuing to use this site, you agree to our use of cookies. Find out more

Member postings for old mart

Here is a list of all the postings old mart has made in our forums. Click on a thread name to jump to the thread.

Thread: How to create a hard edge to your steel.
27/09/2020 18:23:28

Thats exactly how stellite was used.

Thread: Cheap Milling Vice Question
27/09/2020 18:21:15

We have two very good quality Bison 100mm vises which are a similar design as the Soba pictured, and even with hand stoning to tighten them up still exibit the design problems of lifting of the moving jaw. Its something you learn to live with.

Thread: Removing bang in self tappers
27/09/2020 18:13:09

Some careful tapping with a wedge with a similar profile to a wood chisel between the head and the plate, not just in one place, but at several positions. Then as the head starts to lift, a blunter wedge and finally they should be high enough to turn. I would expect them to have a right handed helix.

Thread: Cheap Milling Vice Question
27/09/2020 14:07:29

I bought a 5" model from ARC which opens 6". It is as big as I would ever want to use on the drill mill and too big for the Tom Senior. have used it recently on the TS clamped in line with the X axis. This type of vise is best used without the swivel base attached. The swivel base takes up Z axis space and is best left for those jobs which actually need it. However, it you have the choice between getting the vise with or without the swivel base, always get it as there are rare times when it is worth its weight in gold. They are prone to getting a lot of swarf in them, and need to be dismantled and cleaned regularly. I would think the 3" that you are interested in will work very well with a mini mill, when you get it, check that it is square and will hold your work properly.

Edited By old mart on 27/09/2020 14:10:33

Thread: ER 40 Milling nose
26/09/2020 19:59:28

As long as the length of, say, 110mm from the end of the threads can be 30.5mm then that gives a decent choice of fitted lengths for the larger longer cutters. There needs to be room in the design for spanner flats directly above the nut. Some long spanners will be required as the recommended torque for larger cutters is 145 ftlbs.

I converted a Tom Senior spindle from MT2 to R8 last year and am very pleased with the results. R8 is still a very popular fitting and there is a wide variety of tooling. You would have to make special adaptors if you wanted to use shell mills with an er40 spindle, although there would be no need for a drawbar.

26/09/2020 19:24:47

Since the range of collet sizes is from 3-30mm diameter, to utilise them all fully would need at least 4 diameters accomodated from the face of the nut. A much larger lower half of the spindle would be needed to take a 30.5mm bore. The size of the clamping range of these large collets is such that it is doubtful if cutters in the smaller sizes would be held accurately or tightly enough.

R8 cannot accomodate bigger than 20mm cutters and then only with very limited depth which means that standard length 20mm cutters project a long way.

Edited By old mart on 26/09/2020 19:29:24

Thread: New member from the USA
25/09/2020 14:41:17

Welcome, Ronnie, this forum is a great place for model makers, there is so much expertese. I presume that you are already a member of The Home Shop Machinist forum on your side of the pond, many of their members are also into models.

Thread: Vacuum Pump Advice Please!
24/09/2020 21:16:37

That Edwards pump is capable of going down to 133mB, which may not be enough for your requirements.

Thread: Mounting a collet chuck.
24/09/2020 21:06:26

The backplate is drilled and tapped for three and four jaw chucks. If you would like to preserve the backplate just in case it is needed for a chuck in the future, then an adaptor plate for the collet holder could be made if it will not fit directly.

Thread: Chatter
24/09/2020 20:38:34

450rpm is rather high with that out of balance job hanging so far from the end of the spindle. It might be possible to secure a weight on the workpiece to reduce the out of balance forces.

Thread: fly cutter wear
24/09/2020 20:29:09

Try a file on it, it if you can take anything off then its far too soft. Steel cutting steel always needs oil.

Edited By old mart on 24/09/2020 20:30:16

Thread: Customs payment is it a scam
22/09/2020 15:32:02

If that happened to me, I would get in touch with the Royal Mail, and pass the details to their fraud department.

Thread: Interference
22/09/2020 15:28:20

When I fitted the VFD controlled three phase motor to the Tom Senior, I first chose one with filters for interferance supression. The Vfd is in an earthed steel box, and all the cabling is screened, including the low voltage control wiring. We have not noticed any problems with VHF and DAB radio signals, and the wireless router in the workshop runs as expected.

I had been initially concerned by the manual mentioning an earth leakage when using the filters, but there has been no tripping of any RCD when the mill is in use.

Thread: Hello
22/09/2020 15:19:25

Welcome, Mark, you will find lots of Myford experts and engine makers on this forum, so ask away.

Thread: interest renewed
21/09/2020 18:16:41

That er32 collet chuck will also be very useful when holding work for turning as well as for milling cutters. In the dual function, I would recommend a full set of collets, but if just starting milling, then just buy 3-4-5-6-8-and 10 mm which should match the sizes of cutters likely to start you off with small jobs.

With the 920, you may find it difficult to just move the saddle with enough precision when milling. One way round this is a handle on the end of the leadscrew to move the saddle with the leadscrew nuts engaged, like a lot of Myfords have. Or even more outlandish, the tailstock. When we were refurbishing the apron of the museums Smart & Brown model A, I still needed to use the lathe for turning shafts and bushes with the apron sitting on a bench in bits. I just used the tailstock to push the saddle which saved using the compound which is difficult to use for precision parallel turning.

Edited By old mart on 21/09/2020 18:31:04

Thread: Stuck SDS drill bit
21/09/2020 17:42:26

I cannot imagine just how an SDS drill bit could have turned once fitted, but if the drill is dismantled and the shaft with the chuck is removed and the pneumatic striker is taken out, where the striker fits is a bore right through to the rear of the drill bit. Every time I fit a bit in an SDS drill, I first pull it back and forth to ensure it is correctly fitted, it should slide freely about 10mm.

Thread: Inverter Prolem
21/09/2020 17:23:46

You need to find out which model and power from the inverter. The excellent firm, The inverterdrive supermarket, (google it) sell Teco and they also have the manuals in pdf form. Disconnecting the wires that go into the motor and checking their resistance might throw up any inbalance in the readings, the motor will probably be in delta with three connections and the resistance between any two should match.

Thread: Rivets
20/09/2020 15:04:13

If the application is critical, then I recommend testing first with a replica setup.

Thread: Mystery parts
20/09/2020 15:01:25

Welcome to the forum, Douglas, keep waiting and one of the traction engine/steamroller specialists will see your thread.

Thread: Reminiscences
20/09/2020 14:57:10

I remember when Fairy liquid first came out, and we kids used the empty ones with a little water in them as foam squirters. Corona drinks were all the rage and my favourite was dandelion and burdock. Hula hoops came out after polypropylene tube was first made. I also remember mum taking me to see 20000 leagues under the sea at the cinema in Horsham.

Magazine Locator

Want the latest issue of Model Engineer or Model Engineers' Workshop? Use our magazine locator links to find your nearest stockist!

Find Model Engineer & Model Engineers' Workshop

Sign up to our Newsletter

Sign up to our newsletter and get a free digital issue.

You can unsubscribe at anytime. View our privacy policy at www.mortons.co.uk/privacy

Latest Forum Posts
Support Our Partners
cowells
Sarik
MERIDIENNE EXHIBITIONS LTD
Subscription Offer

Latest "For Sale" Ads
Latest "Wanted" Ads
Get In Touch!

Do you want to contact the Model Engineer and Model Engineers' Workshop team?

You can contact us by phone, mail or email about the magazines including becoming a contributor, submitting reader's letters or making queries about articles. You can also get in touch about this website, advertising or other general issues.

Click THIS LINK for full contact details.

For subscription issues please see THIS LINK.

Digital Back Issues

Social Media online

'Like' us on Facebook
Follow us on Facebook

Follow us on Twitter
 Twitter Logo

Pin us on Pinterest

 

Donate

donate