Member postings for speelwerk

google VOF van de gevel, they have a large selection under klok - veer. Niko

One year after the Brussels atacks again we are shocked by another barbaric act. Regardless of Brexit we as Europa must stay together and form one front against those very sick persons who do this. Niko.

Edited By speelwerk on 22/03/2017 21:20:41

Edited By speelwerk on 22/03/2017 21:30:28

This is perhaps worthwhile buying, they try of course to sell there products but it gives also useful information. Niko.

**LINK**

Before you make adjustments, which should be minimal, mark the position of the split collar and the left adjusting ring for rear bearings. It gives you more control over what you are doing and you can easily return to the original setting. Niko.

Brass of 0.05 mm also cuts easily with a knive around a template. Niko.

Edited By speelwerk on 23/02/2017 12:27:35

When you go with a small 1 mm thick brass strip along the cap, it very quickly takes on the profile of the teeth and takes out all dirt and filings. Niko.

I have had similar with my S7. it turned out it was the no volt release switch which had the contacts burned, so do check that before you take things apart. Niko.

I have used these suppliers end of last year, they were the cheapest for quality goods I could find and were quick with shipping. **LINK**

Niko.

Is it that new dies these days have a lead on both sides since most of the old dies I have only have a lead on one side which very usefull if you want to make a thread go up to the shoulder. Niko.

They say they sell small quantities with a minimum order of 55 euro plus P&P. Niko.

**LINK**

The spacing of the T-slots differ, so you cannot secure the ML7 topslide on the S7 using the T-slots. Niko.

Perhaps this one, Niko

**LINK**

They only have 100 mm, but you can shorten them, Niko.

https://www.schrauben-shop.de/ArticleDetails.aspx?FORMNUMM=1377&Diameter=12

Edited By speelwerk on 18/12/2016 20:31:04

Last week had one on the phone, had a year ago around 3 a day for 2 weeks, best is to answer with some xxxx words and hang up. Niko.

Edited By speelwerk on 30/11/2016 21:29:24

I leveled the 2 lathes I have 15 years or so ago, checked them now and then but no movement at all. They stand on non reinforced concrete on sand, with ground water level at around 10 m. Niko.

I do not think that apart from the leadscrew and rack there differences are between the standard and longbed versions. I know the holes in of the longbed rack does not match that of the standard bed because I stil have a longbed rack waiting to fit onto my standard bed S7 to get the maximum travel out of saddle when all limits are removed. Niko.

Edited By speelwerk on 29/10/2016 22:30:30

Before you bolt is to the floor, do check if the lathe height is comfortable, I with 1.86 m find the original cabinet to low and raised it by 13 cm. Niko.

It is the galley crew taking part in "The Great Britisch Bake off ". Niko.

I would first try to work the inside of the ring with a small hammer, so the inside curve of the ring expands and the diameter gets larger. Niko.

This is widely used in the Netherlands **LINK** on the Dutch website you find more products special for difficult to (soft) solder materials and for stainless which I do not see on the English website. Pure copper has nothing to do with brass which is an alloy of (pure) copper and sinc as already said, perhaps you can ask the supplier for advice. Niko.

Edited By speelwerk on 13/10/2016 21:47:33