By continuing to use this site, you agree to our use of cookies. Find out more

Member postings for Joseph Ramon

Here is a list of all the postings Joseph Ramon has made in our forums. Click on a thread name to jump to the thread.

Thread: Ottowaga Model Locomotive Efficiency Test Trial Event
09/08/2011 15:25:51

Many British model engineers may be unaware that the successful IMLEC events held in the UK have their parallels in other parts of the world. One of the longest standing model steam locomotive events, founded in 1988, is OMLETTE, held in the state of West Victoria and in August 2006 the Ottawanga Rumblers MEC once again ran a successful Ottawanga Model Locomotive Efficiency Test Trial Event. Aside from a break between 1991 and 1997 the event has run annually and attracting competitors from as far away as Alice Springslace and Koala Lumper. The unfortunate break resulted from a little reported feud among Antipodean model engineering club associations. Referred to in hushed tones as the "The Battle of the Boilers" in fact it arose over a dispute about the legitimacy of Briggs Boilers and pulse-jets for competition purposes.

But these sad disputes are long behind us, and the event was in no way marred by the unfortunate destruction of Jim O'Donnel's 0-6-0 Billabong Switcher, "Thangumma Rocket", as it was impossible to prove who had left the points switched to an unbuffered siding.

The Ottawanga track is ground-level six-gauge track, although with only one exception all twelve entrants were using 5" or 7" gauges. The honourable exception was Bruce Hornby's Garden Gauge 6-12-4 'PolyPod', which achieved a remarkable efficiency of 55%. Sadly he was disqualified following spectroscopic analysis of the boiler water which revealed the presence of hydrogen peroxide.

In sweltering heat the competition was good humoured and remarkably free of the violence and track invasions that often characterise the competition. The local competitors did well being used to the rather tar-rich brown coal. Our one oversees competitor, pommey Brian Snivell of the Purley MES, did struggle a little with lighting the fuel. He was eagerly assisted by Rumblers members, but unfortunately the blowtorch they loaned him resulted in the partial destruction of his firebox and he had to retire from the event.

As usual the consumption of coal and water by the locomotives was exceeded solely by the entrants (and observers) consumption of the Amber Nectar. This does create a few problems with making accurate determinations of drawbar pull, particularly in the event of an unscheduled rest-stop at the bottom of the Hooballa Incline. Fortunately this year problems have been reduced through the thoughtful loan of the Sydney Spannerbenders dual 5"/7" Gauge 'comfort car'.

There was small delay at the end of the day, when the laptop computer the Judges were using to calculate the results crashed with a virus from a disk supplied by one of the competitors. In the end, the computer was resurrected and the competition was won by Geoff Hardknott and his 5" Swiss rack-and-pinion loco, with an efficiency of 123%.

One final bit of excitement on the day was the winner's lap of honour, when the club train's vacuum brakes failed completely at about 25 mph. An entertaining disaster was averted by the application of several pairs of shoes directly to the rails. All of which goes to show, of course, that you can't make an OMLETTE without braking legs.

Bill O'Daroy

Secretary

Ottawanga Rumblers MEC

Edited By Joseph Ramon on 09/08/2011 15:27:38

Thread: Measuring the pressure angle of gears
07/09/2010 14:31:49
Flatten out a blob of blu-tac or plasticine on the bench.
 
Roll the gear over the top to leave the impression of a rack. 
 
In principle it should leave a straight-sided impression the angle of the sides being the pressure angle.
 
In practice it won't be perfect, especially if the gears are small, but it should distinguish different angles.
 
Joey 
Thread: What is the ultimate lathe for model engineering
07/09/2010 14:24:16
Norman,
 
By your definition of ultimate, taht would be the undertaker's makeup brush then...
 
Joey 
Thread: N.A. Subscriptions in Disarray
25/01/2010 11:34:11
I have to express sympathy for Dave Clark, whilst understanding the frustration felt by US subscribers.

When the subscriptions changed from Wise Owl, it seems a poor choice of distributor was made, and attempts to remedy that situation are running into the sand.

I have dealt with mailing houses, and know just how much is gained from a trusting relationship with the manager of the mailing house. Now ME just hasn't got the staff, budget or time to pop across and meet with its US mailing house.

Perhaps the ultimate solution would be if Magicalia could stretch to appointing someone external to the mailing houses to be their US Agent on behalf of all their publications (I know others have been affected). Perhaps 2 or 3 days work to straighten the current mess out, then an hour or two a month keeping in contact by phone and a half day visit every few months. It might seem a poison chalice to pick up right now, but it could be rewarding if they were sufficiently interested in the magazine.

Surely someone who lives within 30 miles of the mailing house and occasionally visits the UK on other business wouldn't be that hard to find?


Magazine Locator

Want the latest issue of Model Engineer or Model Engineers' Workshop? Use our magazine locator links to find your nearest stockist!

Find Model Engineer & Model Engineers' Workshop

Sign up to our Newsletter

Sign up to our newsletter and get a free digital issue.

You can unsubscribe at anytime. View our privacy policy at www.mortons.co.uk/privacy

Latest Forum Posts
Support Our Partners
cowells
Sarik
MERIDIENNE EXHIBITIONS LTD
Subscription Offer

Latest "For Sale" Ads
Latest "Wanted" Ads
Get In Touch!

Do you want to contact the Model Engineer and Model Engineers' Workshop team?

You can contact us by phone, mail or email about the magazines including becoming a contributor, submitting reader's letters or making queries about articles. You can also get in touch about this website, advertising or other general issues.

Click THIS LINK for full contact details.

For subscription issues please see THIS LINK.

Digital Back Issues

Social Media online

'Like' us on Facebook
Follow us on Facebook

Follow us on Twitter
 Twitter Logo

Pin us on Pinterest

 

Donate

donate